Search found 514 matches

by Rick Parkington
Wed Aug 15, 2018 12:28 am
Forum: In the shed
Topic: Octopus electrical test bench
Replies: 3
Views: 421

Re: Octopus electrical test bench

That's it; looks like a crazy but useful 50s kitchen that lot!
by Rick Parkington
Mon Aug 13, 2018 10:27 pm
Forum: Pre-war Motorcycles
Topic: unknown bike
Replies: 2
Views: 761

Re: unknown bike

Hi Allen,
That looks awfy like a mid-twenties Dunelt Model K to me.
250cc twin port 2 stroke, great pic!
Cheers Rick
by Rick Parkington
Mon Aug 13, 2018 10:14 pm
Forum: In the shed
Topic: Octopus electrical test bench
Replies: 3
Views: 421

Re: Octopus electrical test bench

Cool thing Dennis! The Magneto Guys have one down my way. I have the Octopus magneto bearing puller (like a lathe chuck on a stand with an extractor bolt screwed through the back) but I'm definitely top trumped by this!
cheers Rick
by Rick Parkington
Fri Dec 22, 2017 1:10 pm
Forum: Pre-war Motorcycles
Topic: Flat Tank Frame Repair
Replies: 2
Views: 2138

Re: Flat Tank Frame Repair

Bit late to reply to this, but seeing as I'm here... Bad pitting on a vintage frame is probably much less risky than having repair work done. My fist flat tanker was very badly corroded having been built up around a frame/forks found rotting outdoors (it cost me a tenner in 1984 so you can guess how...
by Rick Parkington
Fri Dec 22, 2017 12:36 pm
Forum: Pre-war Motorcycles
Topic: ID for Dad's 1930s machine please
Replies: 2
Views: 2730

Re: ID for Dad's 1930s machine please

Hello, I see why you suggest it might be an OK but I'd say it's more likely to be an OEC. The giveaway is the plunger type rear suspension (it's actually swinging arm) and if you blow up the image you can just about make out the large E on the tank. This suspension is more usually seen on the duplex...
by Rick Parkington
Fri Dec 22, 2017 11:46 am
Forum: Technical Advice
Topic: indian bullet gearbox issue
Replies: 2
Views: 1456

Re: indian bullet gearbox issue

Hi folks, long time no speak. I would say that if the bearing if splined to the shaft it will turn with the inner race of the bearing anyway, so there is no reason for the two not to touch. In this case there would usually be a slightly raised ring on the back of the gear - only a fag paper thick - ...
by Rick Parkington
Sat Oct 25, 2014 11:37 pm
Forum: Technical Advice
Topic: Tappet Adjustment spanner size
Replies: 4
Views: 672

Re: Tappet Adjustment spanner size

I find a 4BA open ender works okay for most 5/16 tappet adjusters and you can just about get away with a radiator bleed key on 1/4 diameter ones.
Rick P
by Rick Parkington
Sat Oct 25, 2014 11:27 pm
Forum: Technical Advice
Topic: Triumph Twenty-One engine advice sought
Replies: 36
Views: 3844

Re: Triumph Twenty-One engine advice sought

if you are using points check on both cylinders ,the timing will probably be more advanced on one cylinder than the other.hence the damage is to one piston?? Good point. One of the pillar bolts holding the timing plate on my T140 has a stripped hole so the timing wanders on the top set of points & ...
by Rick Parkington
Sat Oct 25, 2014 11:05 pm
Forum: Technical Advice
Topic: How on earth!
Replies: 10
Views: 1255

Re: How on earth!

Hello all, long time no speak. Just a couple of points, I suspect cars have earth straps because of the heavy current drawn by the starter motor. Yes you will need to make sure there is good earth continuity across painted surfaces. It's true to say the bikes used the frame as an earth when new but ...
by Rick Parkington
Wed Dec 11, 2013 1:29 pm
Forum: Technical Advice
Topic: 1966 tr6r ignition timing
Replies: 9
Views: 804

Re: 1966 tr6r ignition timing

Makes sense but do you really need to remove one set of points to reach the auto advance? The condensers cover big slots in the plate which you could get through - but I've always used a cupped washer under the centre bolt to lock it (two ordinary washers would do, one large enough to sit on the cam...